Looking for:
Download - Spektrum Dx8 Gen1 Manual (Spektrum-Dx8g1-Manual). |
DX8 Instruction Manual - Horizon Hobby
- Spektrum dx8 manual download
Page Differential 2 ailerons 1 flap, 2 ailerons 2 flaps or Elevon is selected in Wing Type highlight SW then rotate to change to the desired switch position or inhibit the see page 13 and each aileron servo is controlled by its own channel. Page Throttle Cut The screen displays a graphic 5-point throttle curve on its left side to aid in selecting throttle curve values.
An Expo function is available that smoothes out the Throttle curve. You can assign up to four separate throttle curves. A graph displays at the left side of the screen to aid in adjusting throttle curves. Page Swashplate Note: Negative and positive swashplate values are available.
Page Governor. Also, you can program the channel the governor controls. The DX8 features a 5-point Pitch curve. You can set up to four separate Pitch curves. A graph displays at the left side of the screen to aid in adjusting pitch curves.
There is an Elevator to Flap in position to highlight the desired rates then rotate the roller to adjust the value. Page Tail Curve For Non-Heading Hold Gyro Use Only To verify that the programmable mix is working properly and in the correct direction, place the correlating switch in the active positions, move the programmed master channel and observe the slave channel. The slave channel should move accordingly. Page Mixing Heli The throttle position should increase.
If it decreases then the opposite value positive vs. The DX8 offers eight mixes in helicopter model type.
You can program a cyclic- to-throttle mix to advance the throttle when aileron, elevator and or rudder inputs are given. Place the flight mode switch in one of the active positions. Page Gyro Also, you can program the channel the gyro gain is controlling. Page 34 Select Inh. Use this as to read low reference value. Page General Information 7. Konus kj-7 telescopio Technical pro rksys How do i get it to stop? I wanted If so, Go HighLevel has the perfect solution for you.
Go HighLevel is a comprehensive sales and marketing platform designed to help e-commerce entrepreneurs drive more sales on their Shop PDF User Manuals. We regularly supplement and update our library. What our users say about us: Peter Morgan: "Thanks for this website! Thanks a lot. Totally happy! The switches are located at the lower front of the transmitter and are used to select the direction of each channel.
Spektrum DX5e Transmitter 2. Ds 6 e spektrum dx6i manual. Specifications: All the goods had been tested well, it is needed to. The DX5e radio brings together the. Only damages are the dx5e has a snapped trainer switch. Spektrum dx18 gen 2 spektrum dx6 manual. Just don't touch the on and off power switch wile flying well that shouldn't be that hard since its in a hole. When charging, SPM and charger SPM , it is necessary to fully be sure to use a charger designed for a 4-cell 4.
The DX5e brings sport RC modelers the unbeatable control of. It is essential to read and follow all the instructions and warnings in the manual,. This diagram is from the instruction manual for the radio system. If you prefer a paper hard copy of a manual listed on this page, you can purchase it from the True Manuals web site. Find the manual or exploded parts view for your. High Quality Transmitter case This manual contains instructions for safety, operation and maintenance.
Want a how-to manual for start-ups? Now there is one. Spektrum DX5E antenna mod. New Trucks with a Manual Transmission. The DX5e incorporates a range testing mode which reduces the output power of the transmitter, allowing a range check. Failure to operate the product correctly can result in damage to the product, personal property and cause serious injury. View the manual for the Spektrum DX5e here, for free. I am guessing that the red light means low voltage and the. Slide the pins on the bottom of the fin through the holes of the stabilizer and into those in the fuselage.
Spektrum DX5e Manual. Transmitter Specific Binding Instructions. D5e the trainer switch and pull and hold the Elevator trim button backward. DX5e remote control pdf manual download. Spektrum dx5e 5-channel full range 2.
User manual Spektrum DX5e English. This is a sophisticated hobby product. Always purchase products from a Horizon Hobby, Inc. The DX5e is now also equipped with a 3-position switch!. Thanks for watching like or subscribe. Learn more about where to look for car manuals and additional literature. Manual Spektrum DX5e page 8 of 19 English.
In the Comanche Nation in , a fierce and highly skilled warrior named Naru learns the prey she is stalking is a highly evolved alien with a. This is a sophisticated hobby product and NOT a toy. Spektrum DX5e These questions are basic but I couldn't find anything in the manual or here.
Now rotate the roller to adjust theflap speed. The flap speed affects the flap and elevatorcompensation. The flap and elevator will reach their flap positions at the same time. Rotate the roller to change the Swashplate value, noting that positive and negativevalues are available. Repeat the above process for all three cyclic inputs aileron, elevator and pitch. SwashplateThe Swashplate screen adjusts the amount and direction of travel for the aileron,elevator and pitch functions when you activate CCPM mixing in Swash Type seepages An E-ring function also preventsservo over-travel when simultaneous extreme aileron and elevator inputs are given.
Unless using a linear servo or a type of linkage that eliminates this effect, youshould turn on the Expo function when any CCPM mix is enabled. Swashplatevalues increase or decrease the overall control travel of the selected channel. Forexample if you increase Pitch value, the travel of all three servos that control pitchwill increase. If you increase aileron, the aileron and pitch servos will increase. Increasing or decreasing this value affects the travel of that function and not theindividual servo.
Note: Negative and positive swashplate values are available. Adjusting the Governor ValuesRotate the roller to select the desired governor value. Press to access. Rotate toadjust the value. Note: the displayed value is the corrected governor value. GovernorThe Governor function adjusts engine rpm when using a Governor or throttlelimiter.
You can program up to four governor values to be selected from a varietyof switches including the flight mode switch. You can adjust Governor values in. Also, you can program thechannel the governor controls. Repeat this for all desired governor values. You can set up to four separate Pitchcurves. A graph displays at the left side of the screen to aid in adjusting pitchcurves.
An Expo function is available that smooths out the curve. To Program Pitch CurvesWith the transmitter on and the main or telemetry screen displayed, press theroller.
To Activate the Governor FunctionWith the transmitter on and the main or telemetry screen displayed, press theroller. Rotate the roller to highlight Governor then press to access that screen. Rotate the roller to highlight Pitch Curve then press. To activate the Governor function, rotatethe roller to highlight Inhibit; then, press to access the switch function. Selectthe desired switch to control the governor then press the roller to access theGovernor screen.
Selecting a Flight ModeHighlight the desired flight mode at the top of the screen. Press the roller toselect. The selected flight mode will darken to confirm the selection.
The governor and the gyro must use two different channels. If the gyro functionuses a channel, it will not appear in the governor list. Rotate the roller to highlight Ch: channel then press to access that function. Select the channel the governor will be plugged into. Normally Aux 2 is used. Press to access that value. ENAileron to Rudder MixRotate the roller to adjust the selected point to the desired output position.
Use Aileron to Rudder mixing to overcome adverse yaw characteristics withcertain types of aircraft such as the J3 Cub and make coordinating turns easier. To access Aileron to Rudder MixIIf you accessed the flap option in wing type in the system setup mode, theelevator to flap mix will display.
The aileron to rudderMix screen appears. If you select On, the mix will always be on. MixingThe DX8 offers eight mixes in airplane model type. There is an Elevator to Flapmix, Aileron to Rudder mix, and six user-programmable mixes that allow themixing of any channel to any other channel.
Note that both rates areboxed. Moving the aileron stick right or left causes the right or left value only tobe highlighted so you can adjust the values individually. Move the aileron stickin position to highlight the desired rates then rotate the roller to adjust the value.
Pressthe roller to accept the rate. Verify the aileron to rudder mix is working properly and in the correct direction byplacing the active switch in the active position and moving the aileron stick notingthe rudder position. If the rudder moves in the opposite direction than desired,the opposite value positive vs. Note: the Elevator to Flap mix operates in the same fashion as alieron torudder mix. Programmable MixesProgrammable mixes allow any channel to be mixed to any other channel or toitself.
Popular programmable mixes include rudder to steerable nose wheel, dualrudder mix, dual elevator mix, rudder to aileron and rudder to elevator mix forknife edge correction. Rotate the roller to highlight Mixing then press. Note that the Elevator to Flap mixappears on the screen if the appropriate wing type is selected. Now rotate the roller to select programmable Mix, 1, 2,3, 4, 5, or 6 and press the roller. The Mix screen appears. The slave is the channel, themaster will be mixed to.
The slave channel will follow the master channels inputbased on the rate that is programmed. Rotate the roller to highlight the left INH then press the roller to access the masterchannel. Rotate the roller to select the desired master channel.
When selected,press the roller to accept that master channel. OffsetThe offset function establishes the point at which the two mix rates converge. If an offset is needed do the following:Programming an OffsetRotate the roller to highlight Offset then press the roller to highlight the Offsetrate. Rotate the roller to adjust the value. Press the roller to accept the offsetvalue.
Rotate the roller to highlight the right INH then press the roller to access the slavechannel. Rotate the roller to select the desired slave channel. When selected,press the roller to accept that slave channel. Trim IncludeThe trim include function applies trim to the slave channel when the masterchannel you select is a channel that has trim throttle, aileron, elevator andrudder. Typically, this is used when more than one channel is used to operate aprimary control surface dual rudder servos, etc.
Activating Trim IncludeRotate the roller to highlight Trim. Assigning a Programmable Mix to a SwitchRotate the roller to highlight Sw: at the bottom of the screen. Adjusting Programmable Mix RatesRotate the roller to highlight the desired rate then press the roller to highlight thatrate.
You can assign four separate Tail curves or a common Tailcurve to 2 or more flight modes. A graph displays at the left side of the screen tohelp you adjust the Tail curves.
An Expo function is available that smooths outthe curve. Note: Only use tail curves when the gyro is in the conventional gain nonheadinghold mode. To Program Tail CurvesWith the transmitter on and the main or telemetry screen displayed, press theroller. To verify that the programmable mix is working properly and in the correctdirection, place the correlating switch in the active positions, move theprogrammed master channel and observe the slave channel.
The slave channelshould move accordingly. ENRotate the roller to highlight Tail Curve then press. Selecting a Flight ModeHighlight the desired flight mode at the bottom of the screen then press to select. Note that the selected flight mode will darken confirming the selection. Six programmable mixes allow the mixing of any channel to any other channel. You can assign Mixes to activate in various flight modes as well as with the gearswitch. To Access the Mixing FunctionsWith the transmitter on and the main or telemetry screen displayed, press theroller.
The Cyclic to throttle mix appearson the screen. Adjusting the CurveMove the flight mode switch in the position you wish to adjust the curve to. Cyclic-to-Throttle MixCyclic-to-throttle mix prevents rpm decay when aileron, elevator and or rudderinputs are given.
This mix advances the throttle position with cyclic or ruddercontrol to maintain rpm. At full throttle, programming prevents the throttle fromoverdriving the servo. Important: When using a governor, Cyclic to throttle mix is not recommended. Assigning Cyclic Mix to a Flight Mode s Rotate the roller to highlight the desired box at the bottom of the screen. Press theroller to darken the box and activate Cyclic Mix in that flight mode position.
Youcan highlight more than one flight mode position. If all boxes are highlighted, theC Mix function is always on. If no boxes are highlighted, the function is always off. Adjusting Cyclic Mix RatesRotate the roller to highlight the desired rate then press. Rotate the roller to adjustthe value. Adjust the rates for all desired channels. MixingThe DX8 offers eight mixes in helicopter model type. You can program a cyclicto-throttlemix to advance the throttle when aileron, elevator and or rudder inputsare given.
This prevents rpm decay during cyclic and rudder inputs. Move the programmed cyclic orrudder channel noting the throttle position. The throttle position should increase. If it decreases then the opposite value positive vs.
When adjusted correctly, the Swashplatecauses the helicopter to roll and pitch accurately with minimal inter-reaction. Select Swashplate and press the roller. The Swashplate Mix screen appears. Select programmable Mix, 1, 2, 3, 4, 5, or 6 and press the roller. Assigning Swashplate Mix to a Flight Mode s Rotate the roller to highlight the desired box at the bottom of the screen. Press theroller to darken the box activating Swash Mix in that flight mode position.
You canhighlight more than one flight mode position. If all boxes are highlighted, the CMix function is always on. Rotate the roller to highlight the left INH then press to access the master channel.
Select the desired master channel. Highlight the right INH then press the roller to access the slave channel. Selectthe desired slave channel. Adjusting Swashplate RatesRotate the roller to highlight the desired rate then press. Adjust the rate for all desired Swashplate values. Assigning a Programmable Mix to a Flight Mode s Highlight the desired box at the bottom of the screen.
Press the roller to darkenthe box activating programmable mix in that flight mode position. Note you canhighlight more than one flight mode position. If you highlight all boxes, theprogrammable mix function is always n.
If no boxes are highlighted, the functionis always off. Then, move theprogrammed cyclic master channel aileron or elevator to its full travel and holdthis position. Now change the flight mode to a position that the swash mix isinactive in. Note the movement of the slave channel on the left side of the monitor. Adjusting Programmable Mix RatesRotate the roller to highlight the desired rate then press. You can reverse the direction of the slave channel with positive andnegative values.
With helicopters Programmable mixes typically operate scale functions likeretracts, lights, etc. Place the flight mode switch in one of the active positions.
ENMove the programmed master channel while observing the slave channel. Theslave channel should move accordingly. Rotate the roller to highlight Gyro then press to access that screen. OffsetThe Offset function establishes the point at which the two mix rates converge. If an offset is needed normally not in ahelicopter , do the following. Programming an OffsetRotate the roller to highlight Offset then press. To activate the Gyro function, highlightInhibit, then press the roller to access the switch function.
Rotate the roller toaccess the desired gyro control switch. Press the roller to access the Gyro gainscreen. Trim IncludeThe trim include function applies trim to the slave channel when the selectedmaster channel has trim throttle, aileron, elevator and rudder. Typically thisis used when more than one channel operates a primary control surface dualaileron servos, etc.
Activating Trim IncludeRotate the roller to highlight Trim then press. Assigning a Channel- Output You can assign the receiver channel the gyro gain is plugged into in this screen.
A channel used bythe governor function does not appear in the Gyro list. Highlight Ch: channel then press to access the gyro channel function. Select thedesired channel to plug the gyro gain into, normally the Gear channel is used. Adjusting the Rate ValuesRotate the roller to select the desired gain value then press. Select the gain value. Any time a T displays, the gyro is in tail lock Heading Lock. If an N displays, thegyro is in normal mode.
GyroUse the Gyro function to program and adjust gyro gain. You can program up tofour gyro gain values to be selected from a variety of switches including the flightmode switch.
You can adjust gyro gain values in. Also, you can program the channel the gyro gain iscontrolling. The percentage values are the true gain values in eachmode.
To Activate the Gyro Gain FunctionWith the transmitter on and the main or telemetry screen displayed, press theroller. Repeat this for all desired gain values. An alarm sounds whenthe programmed time is reached.
You can program the timer to start using thetrainer switch, the left or right trimmers or automatically when throttle is raisedabove a preprogrammed position. Also, an internal timer that shows run time fora specific model displays on the main screen. To Access the Timer ScreenWith the transmitter on and the main or telemetry screen displayed, press theroller.
Rotate the roller to highlight Timer then press. Throttle 1-time - The timer starts when the programmed throttle position isexceeded and will continue regardless of the throttle position. Throttle - The timer starts when the programmed throttle position is exceeded.
Anytime you lower the throttle below the programmed position, the timer willpause then continue anytime the throttle is raised above that position. This isuseful for flying electric models where the motor run time, not the flight time, isimportant. To Program a TimeRotate the roller to highlight Time then press to access. You can highlight theseconds or minutes. Press the roller to access minutes or second.
This is the stick position where throttle activatesthe timer. Rotate the roller to highlight Stick then press to access the Stick values.
This correlates to the actual throttlestick position. Rotate the roller to select the desired time. You canSelect Inh. To Reset the Internal TimerThere are a couple of ways to reset the internal timer. Rotate the roller to highlightInternal: Reset then press the roller to reset the internal timer to To reset the Count Down or Stop Watch timer on the main screen,press the Clear button.
No comments:
Post a Comment